ERROR CODE B200 PRINTER CANON iP2770
 |
| Canon iP2770 |
ERROR CODE B200 PRINTER CANON iP2770 - Printer problems often become a major influence will print the results we often only think of one job that too in a hurry , especially for children who will undergo a course when the thesis , The following is a problem that often appears on the printer and I will try to describe tips / steps especially at tackle Error B200 Printer Canon iP2770 .
Actually , this step can be applied to many types of printers when subjected to a similar Error , Error is when the printer is governed printing , the light will turn orange and green ngeblink as much as 8 to 10 times . Then the monitor screen dialog box will appear informing an error has occurred on the printer , and you are asked to take off all connections including the power supply and contact the service contact . People will usually say that the workshop was broken and had to replace the logic boardnya . It is said that the price equivalent to the price of a new printer . Once again, just for the sake of saving this step is probably worth you try :
1 . Reset Adapter
a. Turn off the printer . then remove the printer connection with electric current , Disconnect the cable that goes to the printer as well .
b . off adapter . usually located on the back lower left . Also remove it from the bottom . Canon iP2770 is very easy to remove , the other series is rather difficult indeed .
c . Plugg the adapter into a transparent plastic bag . ( from either lebik experience rather thin ) agobelt span ( no leaves on the loose part bag )
d . Enter into the freezer for approximately 8 s / d 12 hours . ( from experience frezer the refrigerator more effectively . purpose is not specifically refrigerators, often fail / not know why )
e . After the cooling time is fulfilled , plug the adapter back into place . Connect with electricity as before .
f . Turn on the printer . Blink is lost and the printer is ready for use .
g . Avoid electrical connection suddenly cut off ( down voltage , power failure ) to prevent recurrence .
2 . Logic reset its
a. Turn off the printer , leave the electrical connection and PC
b . Press the reset button 2 seconds , still hold and press the power button until the green . Then release the button reume while holding the power button .
c . Press and release the button resume 5 x ( ditekanan resistant to 5 ) should light fitting orange flame . Simultaneously and then release the reset button and power.
d . If it is normal , the light will turn green . Wait about 30 seconds to allow the printer cartridge empurna position ( marked by the distinctive sound of the printer ) . After the noise stopped off the printer .
e . Turn on the printer . and the printer is ready for use .
3 . Hack the Printer
Previously sorry. The term is a bit odd , but it usually moves pamungkanya . Because of repeated reset the printer will result in " error " weird . Response less normal printer . It is marked with a blink that 10 x ( normally only 8 x ) , and no meu ketengah cartridge when the cover is opened . And the menu blink wrote canon 10 x ga solution. But you can try these steps :
a. Turn off the printer . Turn again and immediately open the cover , then the cartridge would then turning towards the left edge to the right edge , before it reaches the right edge , blocking the cartridge , the cartridge will stop in the middle. ( Normal )
b . Remove the second cartridge , and close the back cover , then the cartridge box will be drawn on the right . Then roll it will play, let alone to the printer completely silent . ( Approximately 30 seconds ) . Normally orange lights will ngeblink 4 or 5 x .
c . Open the cover of the printer , the cartridge box going to the middle . Replace the cartridge . Close the cover . Wait about 1 minute , let the printer do anything .
d . Once the printer is silent , and the light is green , usually ready for use . Do not directly ordered to print in large quantities . because the cartridge that heat will make this error again repeated .
e . Make it a habit to turn off and unplug the printer connection to a power source , if the error is already overwrite your printer .while the first , may be useful for friend - a friend who was " forced " to saving .
You have just read an article that categorized Driver Resetter
by title "Free ERROR CODE B200 PRINTER CANON iP2770". You can bookmark this page with a URL https://grupdownload.blogspot.com/2013/12/free-error-code-b200-printer-canon.html.
